CJBGG - 96 LINE
- MSDS: CJBGG
- Manufacturer: PPG INDUSTRIES INC
- Product Name: 96 LINE
- National Stock Number: 6850-00F057123
Product Identification
Product ID:96 LINE
MSDS Date:03/05/1997
FSC:6850
NIIN:00F057123
Status Code:A
MSDS Number: CJBGG
Responsible Party
PITTSBURGH, PA 15272-0001
US
Emergency Phone: 412-434-3131
Info Phone: 412-434-3131
Cage: 47695
Contractor
Telephone: 1-800-245-2974 (CAL HYPO)
Cage: 47695
Ingredients
RED IRON OXIDE/IRON (III) OXIDE/FERRIC OXIDE/YELLOW FERRIC
CAS: 1309-37-1
RTECS: NO7400000
Fraction By Weight: 40-<50%
OSHA PEL 10 MG/CUM
ACGIH TLV: 5 MG/CUM (FE)
PHTHALO-GREEN; CI PIGMENT GREEN 7, HYDROUS ALUMINUM
CAS: 1328-53-6
RTECS: GE4300000
Fraction By Weight: 1-<5%
CLAY (KAOLIN), ALUMINUM SILICATE *98-3*
CAS: 1332-58-7
RTECS: GF1670500
Fraction By Weight: 5-<10%
ACGIH TLV: 10 MG/CUM TOTAL DUST
COLUMBIA CARBON, CARBON BLACK, LAMPBLACK, BLACK PEARLS
CAS: 1333-86-4
RTECS: FF5800000
Fraction By Weight: 1-<5%
OSHA PEL 3.5 MG/CUM
ACGIH TLV: 3.5 MG/CUM
C. I. PIGMENT BLUE 15, COPPER PHTHALOCYANINE BLUE
CAS: 147-14-8
Fraction By Weight: 1-<5%
OSHA PEL 15 MG/CUM
ACGIH TLV: 10 MG/CUM
TALC (POWDER), (ASBESTOS FREE), TALCUM; HYDROUS MAGNESIUM
CAS: 14807-96-6
RTECS: WW2710000
Fraction By Weight: 10-<20%
OSHA PEL 2 MG/CUM (RESP DUST)
ACGIH TLV: 2 MG/CUM (RESP DUST)
BARIUM SULFATE, BARYTES *98-3*
CAS: 7727-43-7
RTECS: CR0600000
Fraction By Weight: 1-<5%
OSHA PEL 10 MG/CUM
ACGIH TLV: 10 MG/CUM
ETHYLENE GLYCOL *98-3*
CAS: 107-21-1
RTECS: KW2975000
Fraction By Weight: 5-<10%
OSHA PEL 50 PPM
ACGIH TLV: C 127 MG/CUM
EPA Report Quantity: 1 LB
DOT Report Quantity: 1 LB
Hazards
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:HARMFUL IF INHALED/SWALLOWED.
EYES/SKIN: MAY CAUSE IRRITATION. INGESTION: ETHYLENE GLYCOL MAY
DAMAGE KIDNEYS/LIVER.
Explanation of Carcinogenicity:SEE INGREDIENTS.
Effects of Overexposure:IRRITATION
First Aid
First Aid:INGESTION: GIVE 1-8 OUNCE GLASSES OF WATER. DON'T INDUCE
VOMITING. GENTLY WIPE OUT INSIDE MOUTH TO REMOVE ANY RESIDUAL
MATERIAL. EYES: FLUSH IMMEDIATELY W/A GENTLE STREAM OF LUKE WARM
WATER FOR 15 MIN S. SKIN: FLUSH IMMEDIATELY W/PLENTY OF WATER FOR
15 MINS FOLLOWED BY WASHING W/SOAP & WATER. INHALATION: REMOVE TO
FRESH AIR. GIVE CPR IF NEEDED. OBTAIN MEDICAL ATTENTION IN ALL
CASES.
Fire Fighting
Lower Limits:3.2
Extinguishing Media:USE EXTINGUISHERS APPROPRIATE FOR SURROUNDING FIRE.
Fire Fighting Procedures:WATER SPRAY MAY BE INEFFECTIVE, BUT MAY BE
USED TO COOL CLOSED CONTAINERS EXPOSED TO EXTREME HEAT. IF WATER IS
USED, FOG NOZZLES ARE PREFERRED. USE SCBA.
Unusual Fire/Explosion Hazard:MATERIAL NOT KNOWN TO BE EXPLOSIVE.
Accidental Release
Spill Release Procedures:PROVIDE VENTILATION. ONLY PERSONNEL EQUIPPED
W/PROPER PROTECTED EQUIPMENT SHOULD BE PERMITTED IN THE AREA.
REMOVE ALL SOURCES OF IGNITION. TAKE UP MATERIAL
W/SAND/VERMICULITE/NONCOMBUSTIBLE ABSORBENT. PLACE IN CLEAN EMPTY
CONTAINERS FOR DISPOSAL.
Handling
Handling and Storage Precautions:DON'T STORE >120F.
Other Precautions:IF MATERIAL IS PART OF MULTIPLE COMPONENT SYSTEM,
READ THE MATERIAL SAFETY DATA SHEETS FOR THE OTHER
COMPONENT/COMPONENTS BEFORE BLENDING AS THE RESULTING MIXTURE MAY
HAVE THE HAZARDS OF ALL OF ITS PA RTS.
Exposure Controls
Respiratory Protection:WHERE VENTILATION IS INADEQUATE, USE A NIOSH
APPROVED AIR PURIFYING RESPIRATOR W/THE APPROPRIATE CHEMICAL
CARTRIDGES/POSITIVE PRESSURE, AIR SUPPLIED RESPIRATOR.
Ventilation:GENERAL DILUTION/LOCAL EXHAUST VENTILATION TO KEEP
CONCENTRATIONS TO LOWEST EXPOSURE LIMITS, LEL BELOW STATED LIMITS.
Protective Gloves:RUBBER
Eye Protection:SAFETY GLASSES
Work Hygienic Practices:REMOVE/DON'T REUSE CONTAMINATED CLOTHING,
SHOES/GLOVES.
Supplemental Safety and Health
Chemical Properties
Boiling Pt:B.P. Text:379-475F
Vapor Pres:0.1
Vapor Density:>1
Spec Gravity:2.435
Evaporation Rate & Reference:(BUOAC=1): 1
Solubility in Water:11.4%
Appearance and Odor:VISCOUS LIQUID W/AN ODOR CHARACTERISTIC OF THE
SOLVENTS.
Percent Volatiles by Volume:25.01
Stability
Stability Indicator/Materials to Avoid:YES
STRONG ALKALIES, STRONG MINERAL ACIDS/STRONG OXIDIZING AGENTS
Stability Condition to Avoid:EXTREME HEAT, FLAME CUTTING, BRAZING,
WELDING.
Hazardous Decomposition Products:CO, OXIDES OF NITROGEN, CO2, IRON
OXIDES, OXIDES OF ALUMINUM, CHLORINATED PRODUCTS; OXIDES OF COPPER.
Disposal
Waste Disposal Methods:EMPTY CONTAINERS SHOULD BE RECYCLED/DISPOSED OF
THROUGH AN APPROVED WASTE MANAGEMENT FACILITY. DISPOSE OF
IAW/LOCAL, STATE & FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.